BATH PANELS – Forms & FITTING Guidebook
The subsequent is intended as being a guidebook only and can’t be taken like a definitive or binding document. Suppliers’ instructions when readily available must be adopted, and also the installer should be competent and have an volume of expertise and ability.
Bathtub panels can be found in a number of resources, as well as utilization in addition to the tub set up must be totally viewed as when deciding on a panel.
Acrylic panels – Most important edge water-proof.
They’re moulded sheets created through the bath corporations to accompany their tub ranges. The measurements are confined and allows little or no adjustment to peak; it is actually for that reason vital that they are supplied for fitting at the same time since the bathtub.
The fitter ought to Look at that the peak restriction will likely not have an effect on the plumbing demands ,Which the floor is pretty degree. An allowance for that thickness of the ground covering must also be regarded.
Some acrylic panels are equipped with clips that suit to the ground or beneath the tub rim, however it is advisable that a sub frame is built to maintain the panel in position and help reinforcement. Entrance and finish panel mixtures are reasonably quick as most acrylic panels have moulded ends This is why. Use ‘Velcro’ to hold the panel in position which allows easy access on the plumbing.
Cut with a fine tooth noticed if essential.
Aftercare – Cleanse with cleaning soap and water.
Compact scratches is usually polished out having a rubbing compound.
Veneered or ‘wrapped’ panels – generally offered with unfastened plinths which permit top adjustment.
The standard thickness of those panels is involving 15 and 20mm, which implies that with some bathtub constructions the assist legs and cradles can obstruct the panel. An Original Check out is advisable, remembering to just take into account the unfastened plinth and that is mounted to the back of the leading panel (properly doubling the thickness at this point). A flush end is encouraged. Although it just isn’t incorrect to possess the panel protruding around the bathtub rim, this tends to result in drinking water collecting on the ledge and, in time, penetrating the panel.
Despite the fact that these panels are comparatively solid, a sub body of at the least floor and wall battens should be used.
The benefit of a unfastened plinth cannot be below believed. With the proper order of installation getting advised as:
1. The bath
2. The plumbing.
3. The ground covering
four. The bath panel
Given that the panel is still left right up until final it ought to suit exactly. A unfastened plinth will allow the tolerance shed with a set panel.
Modifying the height of your panel which has a loose plinth.
Evaluate the panel and plinth height, and allow with the plinth to fit and deal with powering the principle panel with an appropriate overlap (Usually a minimum of 40mm); This offers the most peak. Now evaluate the peak on the bathtub from the ground to beneath the rim at both equally ends; if these range plus the bathtub is level then the floor might be out. If the ground is not really but fitted, it is best not to fit the bathtub panel, but an allowance can be built Should the routine would not permit the hold off.
Slicing the panel.
Wherever attainable cutting must be avoided. It compromises the h2o resistance with the complete, and may allow drinking water at the rear of the complete, leading to lifting, and will even allow for water in the sub construction with lucite tube the panel. Just take Exclusive treatment when fitting a sectioned or thorough panel into a recess, to centralise the panel, by cutting either side equally.
Exactly where cuts are essential mark and score the road to be Slash to stay away from splintering. Use a fantastic tooth noticed.
Seal all cuts that has a water-resistant varnish; failure will invalidate the warranty.
Silicone along these cuts when the panel is fitted as it is inescapable They are going to be splashed.
If your bath or its frame stops the panel sitting down absolutely beneath the rim, the panel is usually notched or device rebated (In case the obstruction operates the full duration in the bathtub as with softwood strengthening battens fitted beneath the rim of numerous baths). A rebate should by no means be in excess of half the thickness of the panel body, or encroach into any panelled depth that is thinner when compared to the body. The rebate must then be sealed with varnish and the highest edge with silicone sealant.
